manualshive.com logo in svg

Miele PG 8591, Operating Instructions Manual

Share
Download
Miele PG 8591 Operating Instructions Manual Download Page 148

Programme chart

148

Programme

Use

Pre-wash

1

2

3

(Free memory)

Programmable programme for special applications;
programming by arrangement with the 

Miele

 Customer

Service Department.

(Free memory)

Programmable programme for special applications;
programming by arrangement with the 

Miele

 Customer

Service Department.

Vario TD Dental

Cleaning and disinfection programme according to
EN ISO 15883 for processing wash loads with 

normal

soiling.

(x)

CW

1 Min

Vario TD

Washing and disinfection programme with increased
wash pressure and increased water levels according to
the Vario TD Dental programme.

Programme for the combination of the upper basket

A 105/1

 and the module 

A 315

.

CW

1 Min

Vario TD Intensive

Cleaning and disinfection programme according to
EN ISO 15883 for processing wash loads with 

heavy

soiling.

CW

1 Min

Special 93°C-10'

For cleaning and thermal disinfection at 93 °C with
10 minutes temperature holding time (exposure time).

Rinsing

Programme for rinsing the wash cabinet, for flushing out
brine (see “Water softener/Adding salt”) or for rinsing
heavily soiled load items, e.g. for pre-rinsing soiling,
residual disinfecting agent or to prevent items drying
out and to prevent incrustation before running a full
load.

Drain

For draining wash water, e.g. after a programme
cancellation (see “Operation/Cancelling a programme”).

Summary of Contents for PG 8591

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands