manualshive.com logo in svg

Miele PG 8591, Operating Instructions Manual

Share
Download
Miele PG 8591 Operating Instructions Manual Download Page 132

Problem solving guide

132

Printer/interface

Problem

Cause and remedy

Serial printer fault: no paper

The printer has run out of paper.

Replenish the paper.

Serial printer fault: offline

The washer-disinfector cannot connect to the printer.

Switch the printer on.

Check the connection between the washer-disinfector
and the printer.

If in doubt, have the configuration of the interface
checked by a suitably qualified person.

If the printer has been replaced, the printer type must be
adjusted in the interface configuration.

Serial printer fault: general
fault

The printer is not ready for operation.

Check the printer for fault messages.

Change the printer cartridge if necessary.

Network down

The communication module has identified a network
interruption or cannot establish a connection.

Consult your network administrator.

If the problem cannot be resolved:

Contact the Miele Customer Service Department.

Summary of Contents for PG 8591

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands