manualshive.com logo in svg

Miele PG 8581, Operating Instructions Manual

Share
Download
Miele PG 8581 Operating Instructions Manual Download Page 79

Additional settings

79

Test program

Various programs are available for monitoring cleaning performance
in routine testing.

See “Maintenance” for more information on these programs.

Filter maintenance

Cleaning the fil-
ters in the
wash cabinet

The filters in the wash cabinet must be checked daily and cleaned
regularly; see “Maintenance/Cleaning the filters in the wash cabinet”.

A counter in the controls can be activated to remind you of the re-
quired cleaning at regular intervals.

Cleaning the
A 800 tubular filter

The A 800 tubular filter can be used in special injector bars on various
mobile units and baskets and must be cleaned regularly. Follow the
cleaning instructions in the operating instructions for the tubular filter.

A counter in the controls can be activated to remind you of the re-
quired cleaning at regular intervals.

Activating and
setting the inter-
val

Open the menu as follows:

 button

    

 

Additional settings

        

 

Filter maintenance

            

 

Filter combination

 and/or 

Tubular filter

Inactive

Active

Inactive

Active

Filter combination

Tubular filter

-

Active

The cleaning interval is activated. 
The 

Active

 selection allows you to reset the counter or set the

cleaning interval.

-

Inactive

The cleaning interval is deactivated.

Use the 

 and 

 arrow buttons to select an option and press 

OK

 to

confirm your selection.

Summary of Contents for PG 8581

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands