Miele PDR 908 EL Operating And Installation Instructions Download Page 78

Page: 78 / 96

Supervisor level

"Display" off status

The display switches off to save
energy; only the

Start/Stop

sensor

flashes slowly. This can be changed.

Changing this setting leads to increased
energy consumption.

–

Off

Not switching off

–

On (10 min.) Not curr.prog.

The display will remain on while the
programme is running but will go out
10 minutes after the end of the
programme.

–

Logo (10 min.) Not curr.prog.

The display will remain on while the
programme is running but the logo
will light up 10 minutes after the end
of the programme.

– Factory setting:

On after 10 min.

The display switches off after
10 minutes.

–

On (30 min.) Not curr.prog.

The display will remain on while the
programme is running but will go out
30 minutes after the end of the
programme.

–

Logo (30 min.) Not curr.prog.

The display will remain on while the
programme is running but the logo
will light up 30 minutes after the end
of the programme.

–

On after 30 min.

The display switches off after
30 minutes.

"Machine" off status

In order to save energy, the tumble
dryer will switch off automatically after
the end of the programme or if no
further selection is made. This can be
changed.

Changing this setting leads to increased
energy consumption.

– Not switching off

– Factory setting: Switching off after

15 minutes

– Switching off after 20 minutes

– Switching off after 30 minutes

Delay start

The delay start (Timer) can be
activated or deactivated.

– Factory setting: Off

– On

Summary of Contents for PDR 908 EL

































































































Search results

Summary of Contents for PDR 908 EL

Reviews:

Related manuals for PDR 908 EL

Brands by name

Popular brands

Miele PDR 908 EL, Operating And Installation Instructions

Search results

Summary of Contents for PDR 908 EL

Reviews:

Related manuals for PDR 908 EL

Brands by name

Popular brands