manualshive.com logo in svg

Miele PDR 507 HP, Operating And Installation Instructions

Share
Download
Miele PDR 507 HP Operating And Installation Instructions Download Page 21

Operating the tumble dryer

21

Symbols in the display

Extras

: Use the 

Extras

 sensor to add Extras to a drying programme.

Low temperature:

 The 

Low temperature

 sensor allows you to reduce the

mechanical stress placed on the items while drying.

Anti-crease:

 The 

Anti-crease

 sensor allows you to reduce creasing if the

laundry is not removed immediately after the end of a programme.

Delay start:

 Use the 

Delay start

 sensor to set the start time ...

... or the finish time 

... or the time until the programme starts.

Timed drying programme:

 This sensor enables you to select the

duration of a timed drying programme.

Supervisor level

: Use the 

Supervisor level

 sensor to alter the tumble

dryer's settings.

Information:

 This allows you to view the selected options while the

drying programme is running.

Summary of Contents for PDR 507 HP





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands