manualshive.com logo in svg

Miele HG07-W, Operating Instructions Manual, Page: 99 / 124

Share
Download
Miele HG07-W Operating Instructions Manual Download Page 99

Problem solving guide

99

Water inlet fault

Issue

Cause and remedy

The warning buzzer is
sounding. 
One of the following
messages appears in
the display:

 

Open stopcock

The stopcock is closed.

Open the stopcock fully.

 

Water intake

Before rectifying the problem:

Switch the dishwasher off.

The water inlet is restricted.

Open the stopcock fully and start the programme
again.

Clean the filter in the water inlet (see “Cleaning
and care” – Cleaning the filter in the water inlet”).

The water-connection pressure is lower than
50 kPa. 
Seek professional advice.

The on-site connection for the water drainage may
be too low and you will need to vent the water
drainage (see “Installation – Water drainage”).

 

Fault F18

A technical fault has occurred.

Switch the dishwasher off.

Close the stopcock.

Call the Miele Customer Service Department.

The following fault
message appears on
the display during the

SolarSave

 programme:

Intake temperature too low

The intake water has not reached the required
temperature of 45 °C (see “Installation – Water inlet”).

Start the programme again.

If the fault message appears again, select a
different programme.

Summary of Contents for HG07-W





























































































































Reviews:

No comments