manualshive.com logo in svg

Miele HG07-W, Operating Instructions Manual, Page: 101 / 124

Share
Download
Miele HG07-W Operating Instructions Manual Download Page 101

Problem solving guide

101

Fault in the AutoDos (automatic dispensing)

Issue

Cause and remedy

The message 

Insert PowerDisk or
deactivate AutoDos with OK

appears in the display.

The 

 

AutoDos

 function is active but no PowerDisk

has been inserted.

Insert a PowerDisk (see the “Detergent” chapter,
“Automatic dispensing/AutoDos” section).

If you do not wish to use automatic dispensing,
deactivate the function using 

OK

 or the

 

AutoDos

 sensor control.

The warning buzzer is
sounding. 
The programme does
not start or a
programme that has
already started stops. 
The message 

AutoDos lid open

 appears

in the display.

The lid has not been closed properly.

Close the AutoDos lid and lock it fully (see
“Detergent” chapter, “Automatic dispensing/
AutoDos” section).

If the lid cannot be fully closed, check whether the
PowerDisk holder is lying flat (see “Detergent”
chapter, “Inserting a PowerDisk” section).

If the same fault message appears again, call your
Miele dealer.

The message 

PowerDisk empty.
Deactivate AutoDos with OK

appears in the display.

The 

 

AutoDos

 function is active and the PowerDisk

is empty.

Replace the PowerDisk (see the “Detergent”
chapter, “Automatic dispensing/AutoDos” section). 
If you do not wish to use automatic dispensing,
deactivate the function using 

OK

 or the

 

AutoDos

 sensor control.

The message 

PowerDisk empty.
Deactivate AutoDos with OK

appears in the display
even though you have
inserted a new
PowerDisk.

The dishwasher was switched off when the
PowerDisk was replaced and it has therefore not
recognised the new PowerDisk.

Switch the dishwasher on before replacing the
PowerDisk (see the “Detergent” chapter,
“Automatic dispensing/AutoDos”, “Inserting a
PowerDisk” section).

Summary of Contents for HG07-W





























































































































Reviews:

No comments