manualshive.com logo in svg

Miele G 7966, Operating Instructions Manual

Share
Download
Miele G 7966 Operating Instructions Manual Download Page 103

Frequently Asked Questions

103

Spray arm fault

Problem

Possible cause and solution

During the program and
at the end of the
program, the display
shows the following
message: 

Check spray arms

 

The dishwasher does
not turn off at the end
of the program. 
The dishware may not
be clean because no
detergent was
dispensed. The

AutoDos

 function is

automatically
deactivated during the
program sequence.

The lower spray arm is blocked or the nozzles of the
lower spray arm are clogged. The 

AutoDos

 function

is automatically deactivated during the program
because the AutoDos detergent outlet cannot be
completely flushed out.

Turn the dishwasher off and back on again.

Messages appear in the display.

Perform a rotation check of the lower spray arm
and rearrange the wash items if they are blocking
the spray arm.

Clean the lower spray arm (see “Cleaning the
spray arms” under “Cleaning and care”).

Select 

OK

 to confirm each message.

Start the program again.

Summary of Contents for G 7966





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands