Miele G 7310 Operating Instructions Manual Download Page 108

Page: 108 / 128

Problem solving guide

108

Noises

Problem

Cause and remedy

Knocking noise in the
wash cabinet

A spray arm is knocking against a wash item.



Carefully open the door and rearrange the wash
items that are obstructing the spray arm.

Rattling noise in the
wash cabinet

Wash items are insecure in the wash cabinet.



Carefully open the door and rearrange the wash
items so that they sit securely.

There is a foreign object (e.g. glass shard) in the drain
pump.



Remove the foreign object from the drain pump
(see “Cleaning and care” chapter, “Cleaning the
drain pump” section).

Knocking noise in the
water pipes

This may be caused by the on-site installation or the
cross-section of the piping.



However, this will not affect the functioning of the
dishwasher in any way. If in doubt, contact a suit-
ably qualified plumber.

Summary of Contents for G 7310

































































































































Search results

Summary of Contents for G 7310

Reviews:

Related manuals for G 7310

Brands by name

Popular brands

Miele G 7310, Operating Instructions Manual

Search results

Summary of Contents for G 7310

Reviews:

Related manuals for G 7310

Brands by name

Popular brands