background image

Settings

40

Remote control

This menu option will only be
displayed if you have connected your
dishwasher to your WiFi network (see
“Settings – Miele@home”)

If you have switched on the 

Remote

control

 option, the 

MobileStart

 menu

option is displayed under 

 “Further

programmes/Settings”.

If you wish to permanently switch off
the 

Remote control

 option, you can do

this under this menu option. The

MobileStart

 menu option will then no

longer be displayed.

Even if the 

Remote control

 option is

switched off, you can use Miele to call
up information about your appliance.
However, you cannot start any
programmes or change any settings
from it.

RemoteUpdate

The RemoteUpdate menu option is
only displayed and can only be
selected if the requirements for using
Miele@home have been met (see
“Before using for the first time”
chapter, “Miele@home” section).

The RemoteUpdate function is used for
updating the software in your
dishwasher. If an update is available for
your dishwasher, it will automatically
download it. Updates will not be
installed automatically. They must be
initiated manually.

If you do not install an update, you can
continue to use your dishwasher as
usual. However, Miele recommends
installing updates.

Activating/deactivating

The RemoteUpdate function is
activated as standard. Available
updates will be downloaded
automatically and will only be installed if
you initiate them.

Deactivate RemoteUpdate if you do not
wish any updates to be downloaded
automatically.

Summary of Contents for G 7110

























































































































Reviews: