Miele G 6892 Page 97 Operating Instructions Manual Download

Page: 97 / 112

Settings menu

Settings menu for changing
standard settings

Opening the Settings menu



Switch the dishwasher on with the



button if it is switched off.



Use the programme selector
button



to select the

Further



option.

The first of the further programmes will
appear in the display.



Select the

Settings 

option with the



arrow buttons and confirm with

The first option in the Settings menu will
appear in the display.

To learn about the display, read the
section with the same name.



Use the



arrow buttons to select

the option you want to change and
confirm your selection with

Sub-menu options which have already
been selected will have a tick



beside them.



To exit a sub-menu, use the



arrow buttons to select

Back 

and

confirm with

The display will revert to the menu
above.

Summary of Contents for G 6892

















































































































Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands

Miele G 6892, Operating Instructions Manual

Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands