Miele G 6892 Operating Instructions Manual Download

Page: 20 / 112

Caring for the environment

EcoFeedback consumption
indicator

The

Consumption

function is used for

calling up information about the energy
and water consumption of your
dishwasher (see "Settings menu -
Consumption").

Three different types of information can
be displayed:

– an estimate of the consumption

before the programme begins

– the actual consumption at the end of

the programme

– the total consumption of the

dishwasher

1. Consumption estimate:

After a programme has been selected,
first the name of the programme and,
after a few seconds, the estimated
energy and water consumption will
appear in the display.

The estimated consumption levels will
be displayed as a bar chart. The more
bars (

  

) in the display, the more

energy or water will be used.

The values are influenced by the
programme selected and any
programme options selected.

The display will change automatically to
show the time remaining.

The consumption indicator is switched
on as standard. However, you can also
switch the indicator off (see "Settings
menu - Consumption").

2. Actual consumption

At the end of the programme you can
call up the actual amount of energy and
water used by the programme which
has just been run.



Open the door at the end of the
programme.



Press

when the

Consumption (OK)

message appears in the display.

Switching the dishwasher off at the
end of the programme will delete the
actual consumption values for the
programme which has just been run.

3. "Consumption" setting

The

Consumption

setting gives a total of

the energy and water which has been
used in all previous dishwasher
programmes (see "Settings menu -
Consumption").

Summary of Contents for G 6892

















































































































Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands

Miele G 6892, Operating Instructions Manual

Search results

Summary of Contents for G 6892

Reviews:

Related manuals for G 6892

Brands by name

Popular brands