background image

Programme options

64

Optimise standby

"Optimise standby" is activated by
default.

To save energy, the dishwasher will
switch off automatically a few minutes
after the last time a button has been
pressed or after the end of a
programme.

The dishwasher will not switch off
whilst a programme is running, during
the Delay start period or if there is a
fault.

"Optimise standby" can be switched off
if you prefer. If you do this, the duration
before the dishwasher switches off
increases to 6 hours. Doing this will
increase energy consumption.

Open the door.

Switch the dishwasher off with the 

button, if it is switched on.

Press the programme selector button

 in and, 

whilst holding it in

, switch

the dishwasher on using the 

button. 
Keep the programme selector button

 pressed in for at least 4 seconds

until the lower right-hand programme
indicator comes on.

If this does not happen, start the
procedure from the beginning again.

Press the 

 button 8 times.

The 

 indicator light will flash rapidly 8

times at intervals.

The flashing sequence in the display
shows whether "Optimise standby" is
activated or not.

 

: "Optimise standby" is switched

on.

 

: "Optimise standby" is switched

off.

Press the programme selector button

 if you wish to change the setting.

The setting is now stored in memory.

Switch the dishwasher off with the 

button.

Summary of Contents for G 6660

































































































Reviews: