Miele G 6570 Operating Instructions Manual Download Page 94

Page: 94 / 96

Settings menu

Version info

You can call up the electronic software

version of your dishwasher for technical

support purposes.



Confirm the display with

Showroom programme

For demonstration purposes only.

The dishwasher is equipped with

various demo programmes for

showroom use.

–

Demo mode

Demonstration programme for

showrooms.

–

Demo with sound

This programme activates the

circulation pump to demonstrate the

sound of the dishwasher.

–

Demo AutoOpen

The door will open automatically.

–

BrilliantLight

The interior lighting is on constantly.

Factory default

You can reset all settings to the factory

default settings.



Select

Reset

and confirm with

To close the Settings menu

You can exit the Settings menu using

Finish



Select

Finish

and confirm with

The programme selected will appear in

the display briefly and the indicator light

for the programme selected will come

on.

Summary of Contents for G 6570

































































































Search results

Summary of Contents for G 6570

Reviews:

Miele G 6570, Operating Instructions Manual, Page: 94 / 96

Search results

Summary of Contents for G 6570

Reviews: