Miele G 6570 Operating Instructions Manual Download

Page: 86 / 96

Settings menu

Language



The display can be set to appear in one

of several different languages.
You can change the language in the

display via the

Language 

sub-menu.



Select the language you want as well

as the country, if appropriate, and

confirm with

The flag after the word

Language 

acts as a guide if a language which

you do not understand has already

been set.

If this the case, keep selecting the

option which has a flag after it until

you reach the

Language 

sub-menu.

Time

You can select either a 24 hour or 12

hour clock.
The current time of day must be set

before you can use the "FlexiTimer"

programme option.

Setting the clock format



Select the

Clock format

option.



Select the setting you want and

confirm with

Setting the time of day



Select the

Set

option.



Set the hour with the



arrow

buttons and confirm with

Then set the minutes and confirm

with

The time of day has now been saved.

Summary of Contents for G 6570

































































































Search results

Summary of Contents for G 6570

Reviews:

Related manuals for G 6570

Brands by name

Popular brands

Miele G 6570, Operating Instructions Manual

Search results

Summary of Contents for G 6570

Reviews:

Related manuals for G 6570

Brands by name

Popular brands