Miele G 5266 Operating Instructions Manual Download

Page: 74 / 92

Frequently Asked Questions

Noises

Problem

Possible cause and solution

There is a knocking
noise in the wash
cabinet.

A spray arm is hitting the dishware.



Carefully open the door and rearrange the
dishware that is obstructing the spray arm.

There is a rattling noise
in the wash cabinet.

Dishware is moving around in the wash cabinet.



Carefully open the door and rearrange the
dishware so that it sits securely.

There is a foreign object (e.g., glass shard) in the
drain pump.



Remove the foreign object from the drain pump
(see “Cleaning the drain pump” under “Cleaning
and care”).

Knocking noise in the
water pipes

This may be caused by the on-site installation or the
cross-section of the piping.



However, this will not affect the functioning of the
dishwasher in any way. If in doubt, contact a
plumber.

Summary of Contents for G 5266





























































































Search results

Summary of Contents for G 5266

Reviews:

Related manuals for G 5266

Brands by name

Popular brands

Miele G 5266, Operating Instructions Manual

Search results

Summary of Contents for G 5266

Reviews:

Related manuals for G 5266

Brands by name

Popular brands