Miele DA 3668 Operating And Installation Instructions Download Page 60 | Manualshive

Page: 60 / 72

background image

Installation

60

Setting up for recirculation
mode

If site conditions are not suitable for the
cooker hood to be used with air
extraction, the appliance must be set
up for recirculation. A conversion kit,
available through your dealer of from
Miele is required for operating the
cooker hood in recirculation mode. You
will also need two charcoal filters (see
“Technical data”).

Conversion kit DUU 150 with a plastic
grille is suitable for fitting in a non-
visible area at the top of the wall unit.

Conversion kit DUU 151 with a stainless
steel grille is recommended if the grille
is to be fitted in an area which is visible.



Fit the conversion kit as described in
the installation instructions supplied
with the kit. Make sure that the slats
in the exhaust grille point towards the
centre of the room and not towards a
wall or the ceiling.
A non-return flap is not used in
recirculation mode.



Fit the charcoal filters (see “Cleaning
and care”).

Electrical connection

Refer to the notes in “Electrical
connection” and “Warning and
Safety instructions” before
connecting to the electricity supply.



Connect the cooker hood to the
electricity supply.

«
...
58
59
60
61
62
...
»

Summary of Contents for DA 3668









































































Reviews:

No comments

Related manuals for DA 3668

Brand: VESTEL Pages: 120

Brand: Maan Pages: 2

Brand: Forno Pages: 14

Brand: Neilsen Pages: 4

ESPACE 1200 CENTRALE

Brand: ROBLIN Pages: 1

Brand: V-ZUG Pages: 28

Brand: Baumatic Pages: 3

Brand: Zanussi Pages: 12

Brand: Whirlpool Pages: 16

Brand: Whirlpool Pages: 12

Brand: Whirlpool Pages: 28

Brand: Whirlpool Pages: 20

Brand: Whirlpool Pages: 22

Brand: Whirlpool Pages: 28

Brand: Whirlpool Pages: 32

Brand: Whirlpool Pages: 32

Brand: Whirlpool Pages: 64

Brand: Whirlpool Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands