Miele professional PG 8132 SCi XXL Operating Instructions Manual Download Page 53

Programme options

53

FlexiTimer with EcoStart

The FlexiTimer 

 gives you three ways

of starting the programme by means of
delaying the start. You can set the start
time or the finish time of a programme.
You also have the option of taking
advantage of time variable economy
rates of electricity using the 

EcoStart

function.

When using the FlexiTimer, make
sure that the detergent compartment
is dry before adding detergent. Wipe
dry with a cloth if necessary. If the
compartment is wet, powder
detergent can become lumpy and
stick to the dispenser, with the result
that it is not fully dispensed.

To prevent children coming into

contact with dishwasher detergent:
Do not fill the detergent dispenser

until just before starting the
programme

, i.e. before you activate

the FlexiTimer with 

OK

. Also activate

the door safety lock.

Switch the dishwasher on with the

 button.

The 

Start

 indicator light will flash.

Select the required programme.

Press the 

 button.

You can use the 



 arrow buttons to

select the 

Start at

Finish at

EcoStart

 or

Back 

 function.

Confirm selection of the function you
want with 

OK

.

The current time of day will appear and
the hour number block will be
highlighted.

You can now enter the time you want
using the 



 arrow buttons and

confirm with 

OK

.

If, while you are setting the time, you do
not press any buttons for several
seconds, the display will revert to the
previous menu. You will then have to
enter your settings again.

If the time of day (clock) display has
been switched off (see “Settings menu
- Time of day”), the display will go out
after a few minutes and only the 

Start

indicator light will flash slowly.

Press any button to switch the display
back on again for a few minutes.

Summary of Contents for PG 8132 SCi XXL

































































































Reviews: