background image

 

Service Manual

, 2016-12

 

27

 / 

46

 

2.

 

Remove the clipping strip 

Slowly pull it out 

 

3.

 

Remove the protective cover 

1Pry the protective cover slowly from the upper part, 

2Pull it out and remove it. 

 

4.

 

Remove the starter and protector 

Unplug  the  starter  and  protector  (you  can  use  a 

screwdriver to pry it slowly) 

 

5.

 

The reverse process can complete installation. 

8.7

Display and main control panel

 

Display control board

 

1

 

Remove two screws from the refrigerating air 

duct with a cross screwdriver; 

2

 

Pull all connector terminals out of the 

refrigerating air duct to remove its 

components; 

3

 

Uncover the temperature control indication 

sticker on the cover plate of the air duct; 

4

 

Gently pry out the PCB installation box with a 

straight screwdriver to get the master control 

board and installation box components; 

5

 

Remove 2 screws using a cross screwdriver to 

remove the master control board; 

6

 

Pull out the connector terminal and replace 

the master control board in reverse steps; 

 

Summary of Contents for 22031020000054















































Reviews: