manualshive.com logo in svg

Microsemi SyncServer S600, User Manual

Share
Download
Microsemi SyncServer S600 User Manual Download Page 222

222

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Appendix C  Installing GNSS Antennas
Antenna Kits Overview

Antenna Kits Accessories

Lightning Arrestor

Microsemi offers the lightning arrestor for installations that require antenna coaxial 
lead-in protection. The lightning arrestor passes DC power and frequencies in the 
1.5 GHz range with L1 GNSS antennas. In most installations, the lightning arrestor 
mounts near the point at which the antenna lead enters the facility. See the 

GNSS 

Lightning Arrestor Specifications

, on page 210

 

for specifications.

Lightning does not have to strike the antenna to significantly damage the antenna or 
the GNSS receiver. Damage is often due to the effects of a lightning strike on a 
nearby structure, not a direct strike on the antenna itself. Since lightning strikes may 
induce damaging voltages in the antenna system when striking nearby objects, 
attempt to locate the antenna away from lightning rods, towers, and other structures 
that attract lightning. Also, locate the GNSS antenna lower than any nearby 
structures that are likely to attract a strike. See 

Figure C-2

.

350 ft. Antenna Cable

060-15202-350

424

450 ft. Antenna Cable

060-15202-450

545

500 ft. Low Loss Antenna Cable

060-15202-500

600

750 ft. Low Loss Antenna Cable

060-15202-750

900

900 ft. Low Loss Antenna Cable

060-15202-900

1080

Kit: 

Antenna (112-00079-000)

Mounting Bracket (193-00044-000)

Adapter cable for chassis (060-15202-004)

093-15202-001

46

Kit: 
Lightning Arrestor (112-43400-00-3) with 25 ft. cable

093-15202-002

31

Kit: 
Lightning Arrestor (112-43400-00-3) with 25 ft. low loss 
cable

093-15202-003

30

Kit: 
1:4 Splitter With Two (2) x 3 ft. cables

093-15202-004

44

Inline Amplifier (112-15202-001) with adapter

093-15202-005

1

Table C-1.  GNSS Antenna Kits & Accessories

Antenna Kit

Part Number

Total Delay 

(ns)

Summary of Contents for SyncServer S600





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands