Microsemi SyncServer S600 User Manual Download Page 211

Page: 211 / 252

098-00720-000 Revision B – April, 2016

SyncServer 600 Series User’s Guide

211

Appendix B Specifications and Factory Defaults

Factory Defaults

Factory Defaults

Network

LMR/CNT 240

0.101 dB

Inner Conductor –
0.0032

Outer Conductor –
0.00389

.056 inch diameter
Solid BC

LMR/CNT 600

0.034 dB

Inner Conductor –
0.00053

Outer Conductor –
0.0012

.176 inch diameter
Solid BCCAI

Table B-22. Network > Ethernet Parameters

Description

Default Value

Value Range

Speed

Auto

Auto | Full_100 | Full_1000

IPv4

uncheck/static

IPv4 uncheck | IPv4 check/DHCP | IPv4

check/Static

IP6v

IPv6 uncheck/

autoconfig /static

IPv6 uncheck | IPv6 check/ Autoconfig

uncheck/static |

IPv6 check/Autoconfig uncheck /DHCP |

IPv6 check/Autoconfig check/static |
IPv6 check/Autoconfig check/DHCP

Address (IPv4)

Blank (no value)

[ <ipv4_address> ]

Subnet (IPv4)

Blank (no value)

[ <ipv4_address> ]

Gateway (IPv4)

Blank (no value)

[ <ipv4_address> ]

Address (IPv6)

Blank (no value)

[ <ipv6_address> ]

Table B-21. Antenna Cable Specifications (Continued)

Cable Type

Loss

(@1.575 GHz dB

per foot)

DC Resistance

(



per foot)

Type Center

Conductor

Flammability

Summary of Contents for SyncServer S600





























































































































































































































































Search results

Summary of Contents for SyncServer S600

Reviews:

Related manuals for SyncServer S600

Brands by name

Popular brands

Microsemi SyncServer S600, User Manual

Search results

Summary of Contents for SyncServer S600

Reviews:

Related manuals for SyncServer S600

Brands by name

Popular brands