manualshive.com logo in svg

Microsemi SyncServer S600, User Manual

Share
Download
Microsemi SyncServer S600 User Manual Download Page 128

126

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Chapter 5  
SyncServer S6x0 CLI Command Set

show ip

Use this command to display the current IP settings for all LAN ports.

Command Syntax:

show ip config

The information displayed is consistent with the content shown in the Web Interface 
(Dashboard>Network>Ethernet).

Example:

SyncServer> show ip config

Response:

Eth port config

---------------------------------------------------------
|Port|Speed |IPVersion |IPv4Mode|IPv6Mode|AutoConfig|
|----|----------|----------|--------|--------|----------|
|LAN1|AUTO |ipv4 |DHCP |STATIC |enable |
|....|..........|..........|........|........|..........|
|LAN2|AUTO |ipv4 |STATIC |STATIC |enable |
|....|..........|..........|........|........|..........|
|LAN3|AUTO |ipv4_ipv6 |STATIC |STATIC |enable |
|....|..........|..........|........|........|..........|
|LAN4|AUTO |ipv4_ipv6 |DHCP |DHCP |disable |
---------------------------------------------------------

IPv4 config

---------------------------------------------------------
|Port|Address |Subnet Mask |Gateway |
|----|----------------|----------------|----------------|
|LAN1|192.168.1.100 |255.255.255.0 |192.168.1.1 |
|....|................|................|................|
|LAN2|192.168.99.7 |255.255.255.0 |192.168.99.1 |
|....|................|................|................|
|LAN3|192.168.1.99 |255.255.255.0 |192.168.1.1 |
|....|................|................|................|
|LAN4|192.168.4.100 |255.255.255.0 |192.168.4.1 |
---------------------------------------------------------

IPv6 config

-----------------------------------------------------------------------------
|Port|Address |Pref|Gateway |
|----|--------------------------------|----|--------------------------------|
|LAN1| |0 | |
|....|................................|....|................................|
|LAN2| |0 | |

Summary of Contents for SyncServer S600





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands