manualshive.com logo in svg

Microsemi SyncServer S600, User Manual

Share
Download
Microsemi SyncServer S600 User Manual Download Page 126

124

SyncServer 600 Series User’s Guide

098-00720-000 Revision B – April, 2016

Chapter 5  
SyncServer S6x0 CLI Command Set

history

The command provides a listing of user entries during this session, regardless of 
their validity. If a configuration command provides the configuration value(s) on the 
same entry line as the command, then the configuration value(s) will be shown in 
the history.

Responses are not shown in the history list.

Command Syntax:

history

Example:

SyncServer> history

Response:

0 2015-11-19 18:49:28 set ip address-mode LAN3 ipv4 dhcp
1 2015-11-19 18:49:37 F73
2 2015-11-19 18:49:46 this is not a legal command
3 2015-11-19 18:50:08 show gnss status
4 2015-11-19 18:50:38 set-session-timeout
5 2015-11-19 18:50:47 show-session-timeout
6 2015-11-19 18:50:58 history

The DHCP configuration (item 0) is shown in history because it is accomplished 
on the same line as the command.

The configured session timeout value does not appear (item 4) because the CLI 
prompts for that value on a response line.

Responses to 

F73

 (item 1) and show... requests (items 3,5) do not appear in 

history

Anything entered, even if not valid syntax (item 2) will be maintained in the 
history.

Summary of Contents for SyncServer S600





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands