manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

MMUART Peripherals

UG0331 User Guide Revision 15.0

473

13.2.3

Initialization

This sub-section describes the MMUART initialization sequence, reset, clock requirements, and 
interrupts. The MMUART can be initialized by configuring the MMUART control registers and 
SOFT_RESET_CR system registry.

13.2.3.1 MMUART Initialization Sequence

1.

Release the MMUART from reset by using SOFT_RESET_CR system registry (

Table 465, 

page 474)

2.

Disable the MMUART interrupts by using Interrupt Enable Register (

IER

 

Table 475, 

page 494)

3.

Clear the Transmit and receive FIFO of MMUART by using FIFO Control Register (

FCR

 

Table 470, 

page 491)

4.

Clear the loopback and remote loopback modes by using Modem Control Register (

MCR

 

Table 481, 

page 497)

5.

Configure MMUART to send/receive MSB or LSB as a first bit by using Multi-Mode Control Register 
1 (

MM1

 

Table 486, 

page 501)

6.

Set default transmit and receive ready by using ENABLE_TXRDY_RXRDY bit of FIFO Control 
Register (

FCR

 

Table 470, 

page 491)

7.

Disable 9-bit address flag mode and single wire mode by using Multi-Mode Control Register 2 (

MM2

 

Table 487, 

page 501)

8.

Disable transmit time guard and fractional baud rate by using Multi-Mode Control Register 0(

MM0

 

Table 485, 

page 500).

9.

Set default Receive timeout by using Multi-Mode Control Register 0(MM0) and Receiver Timeout 
Register (

RTO

 

Table 490, 

page 503)

10. Set transmit time guard by using Transmitter Time Guard Register (

TTG

 

Table 489, 

page 503), 

11. Set input filter length to suppress spikes by using Glitch Filter Register (

GFR

 Table 

Table 488, 

page 502)

12. Configure the baud rate of MMUART by using Baud Rate Registers (

DLR

, 

DMR

, and 

DFR

).

13. Set the word length, stop bits and parity of MMUART by using Line Control Register (

LCR

 

Table 480, 

page 496)

14. Disable LIN header detection and automatic baud rate calculation, RZI modulation/demodulation 

and smart card modes by using ELIN(

MM0

), EIRD(

MM1

), and EERR(

MM2

) bits.

MMUART_X_E_MST_SCK Output

High

Enable master clock.
This active High signal is used as a bi-directional enable for the 
SCK_IN and SCK_OUT signals. If these signals are taken from a 
single 
bi-directional pad, E_MST_SCK active High designates Master mode 
and forces the bi-directional pad as an output, otherwise (in case of 
active Low) the pad is an input for SCK_IN.

MMUART_X_OUT1

Output

Low

Output 1.
This active Low output is a user-defined signal. It is programmed by 
the processor via the 

MCR

 and is set to the opposite value. It can be 

used as a bi-directional pad enable for bi-directional topology use 
models.

MMUART_X_OUT2

Output

Low

Output 2.
This active Low output signal is a user-defined signal. It is 
programmed by the processor via the 

MCR

 and is set to the opposite 

value. 

Table 464 • 

MMUART I/O Signal Descriptions 

 (continued)

Name

Type

Polarity Description

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Brand: Panasonic Pages: 45
Barco Argus Information preview
Argus
Brand: Barco Pages: 6
Gardner Denver AirSmart G2 Installation Manual preview
AirSmart G2
Brand: Gardner Denver Pages: 22
B&G NMEA 2000 Installation Manual preview
NMEA 2000
Brand: B&G Pages: 2
Hanna Instruments BL120 Instruction Manual preview
BL120
Brand: Hanna Instruments Pages: 54
Hanna Instruments BL 983320-0 Instruction Manual preview
BL 983320-0
Brand: Hanna Instruments Pages: 2
Magellan K32IRF User Quick Reference Manual preview
K32IRF
Brand: Magellan Pages: 2
MAKOT UMS-02 Manual preview
UMS-02
Brand: MAKOT Pages: 6
YUGE LCC Series Hardware Manual preview
LCC Series
Brand: YUGE Pages: 69
Quectel EC25 series Command Manual preview
EC25 series
Brand: Quectel Pages: 232
Quectel L76 Reference Design preview
L76
Brand: Quectel Pages: 9
Quectel BC26 Manual preview
BC26
Brand: Quectel Pages: 73
Parker P33 Integration Manual preview
P33
Brand: Parker Pages: 54
RAM RP2000 User Manual preview
RP2000
Brand: RAM Pages: 71
Qtus DuetPro Carrycot Manual preview
DuetPro Carrycot
Brand: Qtus Pages: 52
Matelec FPC-36040 Owner'S Operation Manual preview
FPC-36040
Brand: Matelec Pages: 16
ACL ACL 5500 Installation Manual preview
ACL 5500
Brand: ACL Pages: 20
Elotech R 1300 Description And Operating Manual preview
R 1300
Brand: Elotech Pages: 20

Brands by name

Popular brands

Load more brands