manualshive.com logo in svg

Microsemi SmartFusion2 MSS, User Manual

Download the free Configuration Manual for Microsemi SmartFusion2 MSS, a cutting-edge product designed for seamless integration and optimized performance. Unlock the full potential of this advanced solution by accessing the comprehensive manual, available for download at our website. Get started now and elevate your technological possibilities with ease.

Share
Download
background image

High Performance DMA Controller

UG0331 User Guide Revision 15.0

239

8.2.0.3

DMA Controller

The DMA controller controls and monitors transactions on the source and destination AHB master 
interfaces.

 

When

 

a descriptor is configured, the DMA controller enables the write buffer controller to read 

data from the appropriate source memory (AHB bus matrix or MSS DDR bridge) and transfer it into the 
internal data buffer. In a similar way, the DMA controller enables read buffer controller to read the data 
from the internal data buffer and transfers it to the destination memory. The following figure shows the 
detailed DMA Controller flow.

Figure 123 • 

DMA Controller Flow Chart

8.2.0.4

Write Buffer Controller

The write buffer controller enables the appropriate AHB master (AHB-M1 or AHB-M2) to read the data 
from source memory. To initiate read transfers on the AHB bus, the write buffer controller provides the 
read address and asserts the ready signal

. 

The

 

AHB master acknowledges, and the write buffer 

controller writes the source memory data to the internal data buffer.

If the data buffer is full, the write buffer controller initiates idle transfers on the AHB bus, and asserts 
ready signal when at least one data buffer is available. The write buffer controller pauses the DMA 
transfers when the descriptor pause bit is enabled, and resumes the transfers as soon as the pause bit is 
disabled. When the last count value is reached, the AHB slave acknowledges the last transfer. 

Reset

Is Descriptor

valid? 

Data

Transfer

direction = 1 

Enable write buffer

controller to read

data from MSS DDR

bridge and write to

internal data buffer 

Transfer size

bytes are

transferred to

destination

memory 

successfully 

NO

YES

ERROR

YES

Enable Read

buffer controller

to send data from

internal data

buffer to

MSS DDR bridge 

Enable write buffer
controller to read
data from AHB bus
matrix and write to
internal data buffer 

NO

YES

NO

Enable read

buffer controller

to send data from

internal data buffer

to AHB bus matrix 

Load Descriptor to

internal registers 

Update DMA

Status and

Debug registers 

Summary of Contents for SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartFusion2 MSS

Wasp B2000 Installation Manual preview
B2000
Brand: Wasp Pages: 16
NEC NEAX 2400 ICS Manual preview
NEAX 2400 ICS
Brand: NEC Pages: 149
NEC LED-E012i User Manual preview
LED-E012i
Brand: NEC Pages: 13
Gardena EasyPlus Operator'S Manual preview
EasyPlus
Brand: Gardena Pages: 14
Gardena 1273 Operating Instructions preview
1273
Brand: Gardena Pages: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Brand: Gantner Pages: 4
IFM Electronic Ecomot300 AC2630 Supplementary Device Manual preview
Ecomot300 AC2630
Brand: IFM Electronic Pages: 111
Kamstrup M-Bus Manual preview
M-Bus
Brand: Kamstrup Pages: 36
JFA Electronicos K1200 Instruction Manual preview
K1200
Brand: JFA Electronicos Pages: 29
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Brand: Maguire Products Pages: 47
Magtrol DSP7000 User Manual preview
DSP7000
Brand: Magtrol Pages: 160
QUNDIS Q Water 5.5 Mounting And Installation Instructions preview
Q Water 5.5
Brand: QUNDIS Pages: 2
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Brand: Zamel Pages: 2
Yamaha DCP4S-US Owner'S Manual preview
DCP4S-US
Brand: Yamaha Pages: 2
M-system R3-PD16B Instruction Manual preview
R3-PD16B
Brand: M-system Pages: 10
FrSky R9M Instruction Manual preview
R9M
Brand: FrSky Pages: 2
AAT Holding KaDe KDH-KZ620U Installation Manual preview
KaDe KDH-KZ620U
Brand: AAT Holding Pages: 28
Pulse Shower Spas 3002-RIV-PB-BN Owner'S Manual preview
3002-RIV-PB-BN
Brand: Pulse Shower Spas Pages: 4

Brands by name

Popular brands

Load more brands