background image

Power Over Ethernet Power View Pro User Guide 

 

 

Copyright 

 2013  

Microsemi 

40

 

Rev.1.0, 17-Dec-13 

Analog Mixed Signal Group 

1 Enterprise, Aliso Viejo, CA 92656, USA; Phone (USA): (800) 713-4113, (ROW): (949) 221-7100 Fax: (949) 756-0308 

 
 

9  Recovering from Unknown Username, Password 

The procedure below describes how to recover from a scenario in which the user is unable to access the unit by 
Web or Telnet due to unknown unit username or password. 

 

 

 

NOTE: 

The recovery procedure can be performed only from the user LAN (not over the Internet). User should be 
able to turn the unit power off when needed. All PoE ports need to be disconnected, and the unit should 
have only a single active Ethernet link between 

user’s local LAN and the unit.  

 

For username, password recovery over the network, only user PC or laptop having IPv6 Link-Local address as 
FE80::9C39:DB8b:62DE:7CD4 can be used for the following reasons: 

 

IPv6 Link-Local is limited to local LAN since it is blocked by all routers, meaning that password recovery 
can be done only from the local LAN network, and not over the Internet. 

 

No need to configure laptop or unit IPv6 Link-Local address since it is generated automatically (MAC 
address-based). 

9.1  Summarized Username, Password Recovery Procedure (for Experts) 

1.  Only one Ethernet link may be up, leaving the other Ethernet ports disconnected. 

2.  Make sure no PD device is connected, meaning no power is provided to any of the PD devices.  

3.  Turn unit power Off. Wait 10 seconds or so to make sure the unit is completely off. 

4.  Apply back power to the unit. And wait around 15 seconds. 

5.  The entire procedure described below should be done in less than 

90

 seconds since power was applied 

to the unit. 

6.  Connect to the unit Link-Local IPv6 address over Telnet (use the help of SysLog Server in order to find 

out unit IPv6 Link-Local address). Use 

passwordrecovery

 both as username and password. Trying 

to access the unit using any other known unit IPv4/IPv6 address will not lead to recovering the unit from 
unknown username, password. 

7.  Upon successful login, the user will be given the option to restore the unit to factory default, or cancel. 

Selecting the restore option will cause the unit to restore itself to factory default and reset itself. 

8.  After unit reset, the user can regain control over unit configuration by browsing to IPv4 address 

192.168.0.50, using the default username 

admin

, and the default password 

password

 

9.2  Detailed Step-by-Step Username, Password Recovery Procedure  

1.  Please disconnect all except for one Ethernet cable from the unit (only one Ethernet port should be 

active). 

2.  Run IPv4 capable SysLog Server on your laptop/PC (make sure the firewall is turned off, or enable 

UDP port 

514

 to pass through).  

3.  Turn the unit off, wait 10 seconds, and turn it back on. A SysLog message similar to the one in Figure 

9-1: Find Unit IPv6 Link-Local address from Power-Up SysLog Report below should appear after 15 
seconds or so. Please identify unit IPv6 address (IPv6 Link-Local address always starts with FE80).  

Summary of Contents for Outdoor Power View Pro













































Reviews: