Safety Information
Important Safety Information
♦
Installation and removal of the PoE Midspan must be
carried out only by qualified personnel.
♦
Only an isolated AC/DC power source should be used
to power up the POE Midspan.
♦
The external power supply for the equipment will be a
listed, direct plug in power unit, marked Class 2, or
listed ITE power supply, marked LPS, which has
suitably rated output voltage and current.
♦
DC
Power Inlet:
The power connector supplied with the PoE Midspan
(included in the package) has 2 terminals; '+' (POS)
and '-' (NEG) (See Figure 2).
The power inlet cables (not included in the package)
must be rated for current capacity of 2 Amperes
(Stranded
tinned copper 16 AWG for each terminal).
Before connecting power inlet cables to the connector
terminals verify that the power source is off.
After inserting a cable inlet to the connector terminals,
tightly fasten all 4 connector screws (See Figure 2).
This clause is optional:
For improved EMI performance, connect chassis
ground connection to "Earth/Ground" connection at
the working area.
There is no safety hazard when the chassis ground
connection is not connected to the "Earth/Ground".
The PoE Midspan "
DATA IN
" and "
DATA & POWER OUT
"
ports are shielded RJ45 data sockets. They cannot be used
to connect telephone wiring. Only RJ45 data connectors
can be connected to these sockets.
The
DC
power source should be situated near the PoE
Midspan and easily accessible. To disconnect the power
from the PoE Midspan, disconnect the
DC
power cord from
either the
DC
power source or from the PoE Midspan power
connector.
The PoE Midspan “
DATA IN
” and “
DATA & POWER OUT
”
interfaces are qualified as SELV (Safety Extra-Low Voltage)
circuits according to IEC 60950-1. These interfaces can be
connected only to SELV interfaces of other equipment.
WARNINGS:
•
Before connecting the PoE Midspan to its power source,
read the installation instructions.
•
Whenever connecting the PoE Midspan to its power source,
follow basic electricity safety measures.
•
A voltage mismatch can cause equipment damage and may
pose a fire hazard. If the voltage indicated on the label is
different from the power outlet voltage, do not connect the
PoE Midspan to this power outlet.
•
Take extra care when connecting the power inlet
terminals, so that '+’ (POS) and '-' (NEG) terminals are
connected to the proper polarity.
Mounting Instructions
Perform the following instructions:
1.
Install two screws in the wall or shelf as shown in Figure 1.
Figure 1: PoE Midspan mounting instructions
2.
Align the PD-9501G/48VDC mounting slots to capture the surface
screws.
Recycling and Disposal
Disposal instructions for old product: The WEEE (Waste Electrical &
Electronic Equipment) national environmental initiatives has been put
place to ensure that products are recycled using the best available
treatment, recovery and recycling techniques so that human health
and environmental protection considerations receive maximum
attention. This product is designed and manufactured with high
quality materials and components, which can be recycled and
reused.
Do not dispose your old product in a general house hold waste bin.
Inform yourself about your local separate collection system for
electrical and electronic products, marked by this symbol:
Use one of the following disposal options :
1. Dispose of the complete product (including its cables, plugs and
accessories) in a WEEE designated collection facility.
2. If you purchase a replacement product, hand your complete old
product over to the retailer. He should accept it as required by the
national WEEE legislation.
Microsemi Corp.
•
Microsemi name & logo are registered trademarks of Microsemi
corp.
•
802.3at is a trademark of IEEE.
Ordering information:
•
Product Name:
Microsemi 9501G/48VDC
•
Part Number:
PD-9501G/48VDC
•
Description:
1-Port 802.3at 4-Pairs Gigabit PoE Midspan,
48VDC input
Document P/N PD-9501G-48VDC_UG Rev. C00
Microsemi 9501G/48VDC
1B
User Guide
2B
1-Port 802.3at
TM
4-Pairs Gigabit
PoE Midspan, 48VDC input.
It is Microsemi’s policy to improve its products as new technology,
components, software, and firmware become available. Microsemi
therefore, reserves the right to change specifications without prior
notice.
Notice
Technical Support
If you encounter problems when installing or using this product,
please consult the Microsemi website at:
http://www.microsemi.com
For technical support, call: +972-9-775-5123
In the USA: 1-877-480-2323
Email: [email protected]
