manualshive.com logo in svg

Microchip Technology Microsemi IGLOO2, User Manual

Share
Download
Microchip Technology Microsemi IGLOO2 User Manual Download Page 62

MDDR Subsystem

Microsemi Proprietary UG0446 User Guide Revision 7.0

51

Figure 31 • 

Memory Configurations

4.

Configure the 

System Clock

 and Subsystem clocks in the 

Clocks

 tab. The following image shows 

the 

Clocks

 configuration dialog.

•

Select the 

On-chip 25/50 MHz RC Oscillator

 

•

Configure 

HPMS_CCC for MDDR_CLK

 

5.

Configure 

HPMS_CLK, APB_0_CLK, FIC_0_CLK clocks 

as 111 MHz and the 

MDDR_CLK

 clock 

as 333 MHz.

Figure 32 • 

Clocks Configuration

6.

Navigate to the 

Memory Map

 tab giving the required data in the rest of the 

System Builder

 tabs.

For more Information on how to use HPDMA, refer to the HPDMA chapter in UG0448: IGLOO2 High 
Performance Memory Subsystem User Guide.

Summary of Contents for Microsemi IGLOO2

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands