manualshive.com logo in svg

Microchip Technology KSZ8061MNX, User Manual

Share
Download
Microchip Technology KSZ8061MNX User Manual Download Page 22

KSZ8061MNX Evaluation Board User’s Guide

DS50002449A-page 22

 2016 Microchip Technology Inc.

2.12

JUMPERS

The board has four jumpers:

• JP1: Install to enable the KSZ8081 (U2) 3.3V regulator. Remove to disconnect 

power from the KSZ8081. Removing power from the KSZ8081 also isolates it 
from the MII bus.

• JP2: When installed, the low voltage regulator (U6) that partially powers the 

KSZ8061 is enabled/disabled by the KSZ8061 SIGD signal. When not installed, 
the low voltage regulator is always enabled. When the KSZ8061 is properly con-
figured, this feature can be used to achieve ultra-low power standby power.

• JP3: (3-pin) Selects the power source for the board. Normally, install a jumper on 

pins 2-3 for power from connector J8. To power the board from header J7 instead, 
install the jumper on pins 1-2.

• JP4: Install to enable the KSZ8061 (U1) voltage regulator. Remove to disconnect 

power from the KSZ8061.

FIGURE 2-9:

LOCATION OF JUMPERS

2.13

KSZ8061MNX STRAPPING OPTIONS

Resistors R36-R44 are used to select optional strapping configurations to the 
KSZ8061MNX. When a resistor is not installed, the internal resistor for each pin pulls 
it to its default level during reset. Installing a resistor pulls the pin to the opposite logic 
level. See the chip data sheet and/or board schematic for details.

Summary of Contents for KSZ8061MNX



































Reviews:

No comments

Brands by name

Popular brands

Load more brands