background image

Preface

 2016 Microchip Technology Inc.

DS50002449A-page 9

RECOMMENDED READING

This user's guide describes how to use KSZ8061MNX Evaluation Board. Other useful
documents are listed below. The following Microchip documents are available and
recommended as supplemental reference resources: 

• KSZ8061MNX/KSZ8061MNG Data Sheet

This data sheet provides detailed information regarding the KSZ8061MNX device.

THE MICROCHIP WEB SITE

Microchip provides online support via our web site at 

www.microchip.com

. This web

site is used as a means to make files and information easily available to customers.
Accessible by using your favorite Internet browser, the web site contains the following
information:

Product Support

 – Data sheets and errata, application notes and sample

programs, design resources, user’s guides and hardware support documents,
latest software releases and archived software

General Technical Support

 – Frequently Asked Questions (FAQs), technical

support requests, online discussion groups, Microchip consultant program
member listing

Business of Microchip

 – Product selector and ordering guides, latest Microchip 

press releases, listing of seminars and events, listings of Microchip sales offices, 
distributors and factory representatives

CUSTOMER SUPPORT

Users of Microchip products can receive assistance through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

Customers should contact their distributor, representative or field application engineer
(FAE) for support. Local sales offices are also available to help customers. A listing of
sales offices and locations is included in the back of this document.

Technical support is available through the web site at:
 

http://www.microchip.com/support

.

REVISION HISTORY

Revision A (March 2016)

• Original Microchip release of this document. This document replaces Micrel docu-

ment “

KSZ8061MNX Evaluation Board User's Guide

” version 1.1 (March 2015).

Summary of Contents for KSZ8061MNX



































Reviews: