manualshive.com logo in svg

Microchip Technology ATmega4809 Xplained Pro, Manual

Share
Download
Microchip Technology ATmega4809 Xplained Pro Manual Download Page 27

6.4 

Revision 5

Engineering samples with part number ATMEGA4809-MFRES are mounted on revision 5 of ATmega4809 Xplained
Pro.

Revision 5 does not have the header footprints for external 3.3V and 5.0V supply to the mikroBUS socket.

6.5 

Revision 4

Engineering samples with part number ATMEGA4809-MFRES are mounted on revision 4 of ATmega4809 Xplained
Pro.

Revision 4 has a new PCB that fixes the SPI MISO/MOSI issue in revision 3.

Revision 4 does not have the header footprints for external 3.3V and 5.0V supply to the mikroBUS socket.

Instead of the crystal documented in 

4.3.1  Crystals

, the 32.768 kHz crystal on ATmega4809 Xplained Pro revision 4

is a Kyocera Corporation ST3215SB32768E0HPWBB 9 pF crystal. This crystal configuration is not optimally matched
and has a capacitance mismatch that causes the oscillation frequency to be off by ~30 ppm.

This revision of the kit has an ATECC508A mounted on the CryptoAuthentication footprint.

Related Links

4.3.1  Crystals
4.3.4  Footprint for CryptoAuthentication Devices

6.6 

Revision 3

Revision 3 is the initially released revision.

Engineering samples with part number ATMEGA4809-MFRES are mounted on revision 3 of ATmega4809 Xplained
Pro.

Pin 10 on the AVR UPDI debug connector (

J202

) is not connected to GND on revision 3 of ATmega4809 Xplained

Pro.

Revision 3 does not have the header footprints for external 3.3V and 5.0V supply to the mikroBUS socket.

Instead of the crystal documented in 

4.3.1  Crystals

, the 32.768 kHz crystal on ATmega4809 Xplained Pro revision 4

is a Kyocera Corporation ST3215SB32768E0HPWBB 9 pF crystal. This crystal configuration is not optimally matched
and has a capacitance mismatch that causes the oscillation frequency to be off by ~30 ppm.

This revision of the kit has an ATECC508A mounted on the CryptoAuthentication footprint.

The SPI MISO and SPI MOSI signals between the EDBG and the ATmega4809 are crossed in this version of the kit.
The image shows the implemented flywire fix.

 ATmega4809 Xplained Pro

Hardware Revision History and Known Issues

©

 2020 Microchip Technology Inc.

 User Guide

DS50002716C-page 27

Summary of Contents for ATmega4809 Xplained Pro


































Reviews:

No comments

Brands by name

Popular brands

Load more brands