background image

 

 

 

 

 

 

 

        

 

Operator’s Manual

fire & ventilation precautions:

.  This unit was designed for outdoor use only.  NEVER operate this unit in 

an enclosed area.  ALWAYS make certain there is adequate air (oxygen) 
for combustion as well as ventilation to prevent the presence of poisonous 

carbon monoxide gases.  Beware of poorly ventilated areas or exhaust fans 

which can cause inadequate combustion or engine overheating.

2.  NEVER operate this unit in the presence of flammable vapors or combustible 

dust, gases or other combustible materials.  (A spark may cause an explosion 

or  fire.)    When  servicing  this  machine,  be  especially  careful  to  properly 

dispose of any flammable materials.  DO NOT spray flammable liquids.

3.  ENGINE FUEL TANK:

a. 

do not smoKe wHile filling engine fuel tanK

b.  NEVER fill the engine fuel tank while the unit is running or hot.  Allow 

the engine to cool two minutes before refueling.

c.  DO NOT refuel indoors or in a poorly ventilated area.
d.  ALWAYS refuel slowly to avoid the possibility of spilled fuel which may 

cause a risk of fire.

4.  DO NOT operate the unit if gasoline is spilled. Wipe unit clean and move 

the unit away from the spill.  Avoid creating any ignition until the gasoline 
has evaporated.

5.  DO NOT store the unit near an open flame or any equipment such as a 

stove, furnace, water heater, etc., which utilizes a pilot light or devices which 
can create a spark.

important

The following is required by California State law, Section 4442 of the California 
Public  Resources  Code.    Other  states  may  have  similar  laws.    Federal  laws 
apply on federal lands.

A spark arrester must be added to the muffler of this engine if it is 

to be used on any forest covered, brush covered or grass covered 

unimproved land.  The arrester must be maintained in effective 

working order by the operator.

See your engine or equipment dealer for spark arrester muffler options.

important safety warnings

Summary of Contents for CBA-2504




















Reviews: