background image

20 

 

 

 

 

 

 

 

 

 

                         CA-Series Operator’s Manual

Mi-T-M

®

 corporation statement of warranty

Mi-T-M

®

 Corporation warrants all parts, (except those referred to below), of your new cold water pressure 

washer to be free from defects in materials and workmanship during the following periods:

 

For Lifetime against freezing and cracking:

 

 

Pump Manifold

 

For Seven (7) Years from the date of original purchase:

 

 

High Pressure Pump

 

For Two (2) Years from the date of original purchase:

 

 

Cart Assembly 

 

Plumbing

 
 

For One () Year from the date of original purchase:

 

 

GFCI 

 

 

Selector Switch

 

For Ninety (90) days from the date of original purchase:

 

 

Trigger Gun/wand   

High Pressure Hose

 

 

Unloader Valve 

 

Strainer/Filter

 

 

Defective  parts  not  subject  to  normal  wear  and  tear  will  be  repaired  or  replaced  at  our  option  during  the 
warranty period.  In any event, reimbursement is limited to the purchase price paid.

eXclusions

.  The engine is covered under separate warranty by its respective manufacturer and is subject to the terms 

set forth therein.

2.  Normal wear parts:
 

 

Pump Packings 

 

Spray Nozzles

 

 

Pump Valves 

 

Detergent Valves

 

 

O-rings 

 

 

Quick Couplings/Screw Connects

3.  This warranty does not cover parts damaged due to normal wear, misapplication, misuse, operation at 

other than recommended speeds, pressures or temperature.  Parts damaged or worn because of the use 
of caustic liquids or by operation in abrasive or corrosive environments or under conditions causing pump 
cavitation are not warranted.  Failure to follow recommended operating and maintenance procedures 
also voids warranty.

4.  The  use  of  other  than  genuine  Mi-T-M  repair  parts  will  void  warranty.  Parts  returned,  prepaid  to  our 

factory or to a Mi-T-M authorized service center will be inspected and replaced free of charge if found to 
be defective and subject to warranty.  There are no warranties which extend beyond the description of 
the face hereof.  Under no circumstances shall Mi-T-M

®

 Corporation bear any responsibility for loss of 

use of the unit, loss of time or rental, inconvenience, commercial loss or consequential damages.

For Service or warranty Consideration, contact

Mi-T-M

®

 Corporation, 8650 Enterprise Drive, Peosta, IA  52068-0050

563-556-7484 / 800-553-9053 / Fax 563-556-235

Monday - Friday  8:00 a.m. - 5:00 p.m.  CST

Summary of Contents for CA-3304-0MHB






















Reviews: