Mi-T-M CA-3304-0MHB Operation Manual Download Page 19

Page: 19 / 21

CA-Series Operator’s Manual

accessories

5-0006

Supply Hose ¾ in.

85-0007

3000 PSI Extension Hose 50 ft.

85-0006

4000 PSI Extension Hose 50 ft.

Aw-3000-0000

Sandblaster Carbide Nozzle (Consult Factory)*

Aw-3020-0000

Sandblaster Ceramic Nozzle (Consult Factory)*

Aw-4085-006

Pump Oil 6 oz.

AW-7003-1500

Rotary Brush

Aw-705-200

Extension wand 2 ft.

Aw-705-800

Extension wand 8 ft.

Aw-705-2400

Extension wand 24 ft.

Aw-703-800

Extension wand 8 in.

Aw-703-3600

Extension wand 36 in.

Aw-703-7200

Extension wand 72 in.

Aw-7300-0003

Rotating Nozzle #3.0 (Consult Factory)*

Aw-7300-0035

Rotating Nozzle #3.5 (Consult Factory)*

Aw-7300-0004

Rotating Nozzle #4.0 (Consult Factory)*

Aw-7300-0045

Rotating Nozzle #4.5 (Consult Factory)*

Aw-7300-0005

Rotating Nozzle #5.0 (Consult Factory)*

Aw-8400-002

Detergent Injector

*PSI and GPM must be specified when ordering.

Mi-T-M All Purpose Cleaner, Paint Surface Prep, House and Deck wash and Heavy Duty
Degreaser are specially formulated detergents for use with all Mi-T-M pressure washers

and are packaged in one (1), five (5) and fifty-five (55) gallon containers. contact Mi-T-M

Customer Service Department at (800) 553-9053 for more information.

Summary of Contents for CA-3304-0MHB






















Search results

Summary of Contents for CA-3304-0MHB

Reviews:

Related manuals for CA-3304-0MHB

Brands by name

Popular brands

Mi-T-M CA-3304-0MHB, Operation Manual

Search results

Summary of Contents for CA-3304-0MHB

Reviews:

Related manuals for CA-3304-0MHB

Brands by name

Popular brands