background image

 

 

 

 

 

 

 

 

 

                         CA-Series Operator’s Manual

installation & preparation

attire:

Proper attire is essential to your safety.  It is advised to utilize whatever means 
necessary  to  protect  eyes,  ears,  and  skin.   Additional  safety  attire  (such  as 
respiratory mask) may be required when using detergent cleaning agents with 
this washer.

setup:

.  This unit should only be placed on a level surface to ensure proper lubrication 

for the engine and water pump while operating.  

2.  Do not use unit in an area:

a.  with insufficient ventilation.

b.  where there is evidence of oil or gas leaks.

c.  where flammable gas vapors may be present.

3.  Be  certain  to  block  the  wheels  to  prevent  the  unit  from  moving  while 

operating.

4.  Do not allow the unit to be exposed to rain, snow or freezing temperatures.    

If any part of the unit becomes frozen, excessive pressure may build up in 
the unit which could cause it to burst resulting in possible serious injury to 
the operator or bystanders.

5.  Once properly installed, check the oil sight glass on the pump crankcase.  

Make certain the oil level is in the center of the sight glass before each use.  
If the level appears low, use Mi-T-M pump oil #Aw-4085-006.  DO NOT 
OVERFILL!

DANGER

risK of eXplosion or fire!
do  not  place  unit  in  an 
area  wHere  flammable 
gas vapors may be present.  
a  sparK  could  cause  an 
eXplosion or fire!

risK of unit bursting!
do not store/operate unit in 
a freezing environment!

WARNING

risK of aspHyXiation!

-do  not  operate  in  an 

enclosed  area.    use  tHis 
p r o d u c t   on ly  in   we l l 
ventilated areas!

-tHe  eXHaust  from  tHe 

engine  contains  carbon 
monoXide,  a  poisonous, 
odorless  and  invisible 
gas.    breatHing  tHis  gas 
can  cause  serious  injury,   
illness & possible deatH.

WARNING

risK of eXplosion or fire!
always  store  fuel  away 
from tHe wasHer wHile tHe 
unit is running or Hot.

DANGER

risK of fire!

- d o   n o t   s m o K e   w H i l e 

fueling!

-do  not  fill  tHe  fuel  tanK 

wHile  unit  is  running  or 
Hot.  allow  unit  &  engine 
to  cool  for  two  minutes  
before refueling.

-do  not  fill  fuel  tanK  to 

point  of  overflowing.  
allow  approXimately  1/4” 
of  tanK  space  for  fuel 
eXpansion.

engine fuel tanK:

.  Review “Fire & Ventilation Precautions” pg. 4, before fueling.

2.  Locate the Safety Decals on your unit and heed their warnings. 

3.  A minimum of 86 octane fuel is recommended for use with this unit.  DO 

NOT MIX OIL wITH GASOLINE.

4.  Purchase fuel in quantities that may be used within 30 days.  Use of clean, 

fresh lead free gasoline is recommended.  Leaded gasoline may be used 
if lead-free is unavailable.  DO NOT use gasoline containing methanol or 
alcohol.

5.  Check  the  engine  oil  level  before  starting  the  engine.    (See  Engine 

manual.)

6.  Fill the fuel tank according to accompanying engine manual instructions.

7.  Occasional  carburetor  and  choke  adjustments  will  be  necessary  for  the 

engine.    Refer  to  the  engine  manual  supplied  with  this  unit  for  proper 
adjustment procedures. 

8. 

Review the engine manual accompanying this pressure washer for 

correct engine start-up and maintenance procedures.

Summary of Contents for CA-3304-0MHB






















Reviews: