MHSC MJ27NR Installation And Operating Istructions Download Page 1

READ AND SAVE THESE INSTRUCTIONS

Unvented Gas Log Heater or  

Vented Decorative Appliance

Installation and Operating Instructions

This is an unvented gas-ired heater. 

It uses air (oxygen) from the room 

in which it is installed. Provisions 

for  adequate  combustion  and 

ventilation air must be provided. 

 

Refer to page 7. 

WARNINGS

If the information in this manual is not followed exactly, 

a ire or explosion may result causing property damage, 

personal injury or loss of life.
–  Do  not  store  or  use  gasoline  or  other  lammable 

vapors and liquids in the vicinity of this or any other 

appliance.

–  WHAT TO DO IF YOU SMELL GAS

  •  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use any 

phone in your building.

 

•  Immediately call your gas supplier from a neighbor's 

phone. Follow the gas supplier's instructions.

  •  If you cannot reach your gas supplier, call the ire 

department.

–  Installation  and  service  must  be  performed  by 

a  qualified  installer,  service  agency  or  the  gas 

supplier.

This  appliance  may  be  installed 
in  an  aftermarket,  permanently 
located,  manufactured  (mobile) 
home,  where  not  prohibited  by 

local codes.

This  appliance  is  only  for  use 
with the type of gas indicated on 

the rating plate. This appliance is 

not convertible for use with other 

gases.

MODELS: MJ27NR, MJ27PR 

Natural Gas or Liquid Propane

 

Control Type: Millivolt  Hi/Low

86D0024  10/08  Rev. 1

Summary of Contents for MJ27NR









































Reviews: