manualshive.com logo in svg

MG Energy Systems MGRS12S4P176, Manual

Share
Download
MG Energy Systems MGRS12S4P176 Manual Download Page 35

 

 

MG Energy Systems B.V. | Foeke Sjoerdswei 3 | 8914 BH Leeuwarden | The Netherlands  

+31 (0)58 750 89 47 | [email protected] | www.mgenergysystems.eu 

Innovation

 in energy storage 

8.4

 

Electrical connection procedure 

The battery module can be used in combination with other battery modules of the same type and 
always in combination with a master BMS. 

 

Power connection procedure 

The power connections make use of the Amphenol PowerLok™ connectors. See section 7.2.2 for 
detailed information about types and cable sizes available. 

 

ELECTRICAL HAZARD: 
The battery modules can be placed in series up to 900 VDC. Make sure to wear 
proper insulation gloves. 

 
Follow this procedure to connect the Amphenol PowerLok™ connectors to the battery module: 

1.

 

Plug in the Amphenol PowerLok™. 

 

 

NOTICE: 
Orange is the positive terminal of the battery and black is the negative terminal of 
the battery. This cannot be switched because connectors are keyed. 

 

2.

 

Push the orange/black lip forward to lift the locking mechanism. 

 

Summary of Contents for MGRS12S4P176




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands