background image

MFJ-1775 Rotatable Mini-Dipole 

                                                 Instruction Manual 

 

 

1

MFJ-1775 PARTS LIST 

 

As you unpack your antenna you should find the parts in the following list. 

 

Part Description 

 

 

QTY  MFJ Part No. 

Balun 

    1 

80-1775-10

 

6-32 x 3/8” screw 

 

 

80 

656-0375S 

¼-20 x 1-3/4 bolt 

 

 

662-1760S-HH 

6-32 

kep 

nut 

   80 

705-0632S 

10-32 

hex 

nut 

   10 

705-1032S 

¼-20 

hex 

nut 

   4 

705-2520S 

#10 lock washer 

 

 

711-1037S-EX 

¼ split lock washer 

 

 

711-2537S-SL 

Hose clamp (#16) 

 

 

745-3116S 

16” Threaded Rod (2M stub) 

 

758-8252 

55” Threaded Rod (6M stub) 

 

758-8253 

640 

U-bolt 

Set 

   2 

758-9200 

1/8” Plastic Spoke Caps  

 

35 

765-1002 

Aluminum “L” Stabilizer Bracket 

805-1796-7 

Fiberglass Stabilizer Insulator   

807-1796-6 

Aluminum Stub Channel Bracket 

808-1796-5 

1 x 12” Fiberglass Rod   

 

808-1775-12

 

1-1/8 x 60” AL Tube 

 

 

810-1796-2 

30” LONG Spokes 

 

 

810-1796-3C 

26” MEDIUM Spokes   

 

810-1796-5C 

12” SHORT Spokes 

 

 

24 

810-1796-6C 

Loading Coil Assembly  

 

811-1796-1C1 

 

For installation, you will need some items not supplied with the antenna installation kit: 

• 

A 6'-8' rigid mast or other mounting pipe between 1" and 1.5" outside diameter. (suitable materials 

include TV mast sections, galvanized iron pipe, or heavy duty rigid conduit.) 

• 

Quality low-loss 50-Ohm coax with a PL-259 from antenna to transmitter. 

An Antenna Analyzer (MFJ-259B or similar), or SWR meter and transceiver

 

 
 
 
 
 
 
 
 
 

 

INRADIO
ABEL & PRO-FIT Centrum Radiokomunikacji

tel.

fax:

e-mail:
internet:

ul. Puszkina 80

92-516 £ódŸ

Poland

(+42) 649 28 28

(+42) 677 04 71

[email protected]

www.inRADIO.pl

Autoryzowany Przedstawiciel MFJ w Polsce:

Summary of Contents for MFJ-1775













Reviews: