background image

1

INTRODUCTION

These operating instructions provide important information 
about the form, features, function, and specifications of the 
MJF-212A

 high-power stage monitor. 

Chapter 1: Introducing mJf-212A

 provides a general 

description of MJF-212A and its capabilities and 
functionality.

Chapter 2:

 

Power Requirements 

discusses power 

distribution and voltage and current requirements, as well 
as electrical safety issues.

Chapter 3: Amplification and Audio

 will help you 

understand and harness the power of the MJF-212A 
amplifier. Amplifier specifications, connectivity, limiting, and 
the cooling system are all covered.

Chapter 4:

 

RmS™ Remote monitoring System

 introduces 

the optional RMS communication module that can be 
installed in the MJF-212A amplifier to make use of Meyer 
Sound’s RMS remote monitoring system.

Appendix A:

 

Optional VEAm multipin Connector 

includes information on the optional factory-installed VEAM 
Connector.

Appendix b:

 

Specifications and Dimensional Drawings

 

provides detailed acoustic and electrical specifications for 
the MJF-212A monitor, along with detailed dimensional 
drawings.

HOw TO USE THIS mANUAl

As you read this manual, you’ll find figures and diagrams 
to help you understand and visualize what you’re reading. 
You’ll also find icons that flag important information or warn 
you against improper or potentially harmful activities. These 
icons include:

         

A

 NOTE 

identifies an important piece of 

information relating to the topic under 

discussion.

TIP 

offers a helpful tip relevant to the topic 

at hand. 

CAUTION

 gives notice that an action can 

have serious consequences and could cause 

harm to equipment or personnel, delays, or other 
problems.

Information and specifications are applicable as of the date 
of this printing. Updates and supplementary information are 
posted on the Meyer Sound website at:

     http://www.meyersound.com

You can contact Meyer Sound Technical Support at:

     Tel: +1 510 486.1166

     Fax: +1 510 486.8356

     E-mail: [email protected]

INTRODUCTION

Summary of Contents for MJF-212A





























Reviews: