Meyer Sound Compact VariO UPJ-1P Operating Instructions Manual Download Page 18

12

CHAPTER 5

SIM MEASUREMENT SYSTEM

SIM is a measurement and instrumentation system 
including a selection of hardware and software options, 
microphones and accessory cables. SIM is optimized for 
making audio frequency measurements of an acoustical 
system with a resolution of up to 1/24 of an octave; the 
high resolution enables you to apply precise electronic 
corrections to adjust system response using frequency and 
phase (time) domain information.  

Source Independent Measurement Technique

SIM implements the Meyer Sound source independent 
measurement technique, a dual-channel method that 
accommodates statistically unpredictable excitation signals. 
Any excitation signal that encompasses the frequency range 
of interest (even intermittently) may be used to obtain highly 
accurate measurements of acoustical or electronic systems. 
For example, concert halls and loudspeaker systems may 
be characterized during a musical performance using the 
program as the test signal, allowing you to:

 

View measurement data as amplitude versus time 
(impulse response) or amplitude and phase versus 
frequency (frequency response)

 

Utilize a single-channel spectrum mode

 

View frequency domain data with a logarithmic 
frequency axis

 

Determine and internally compensate for propagation 
delays using SIM Delay Finder function

Applications

The main application of SIM is loudspeaker system testing 
and alignment. This includes:

 

Measuring propagation delay between the subsystems 
to set correct polarities and set very precise delay times

 

Measuring variations in frequency response caused 
by the acoustical environment and the placement 
and interaction of the loudspeakers to set corrective 
equalization

 

Optimizing subwoofer integration

 

 Optimizing loudspeaker arrays

SIM can also be used in the following applications:

 

Microphone calibration and equalization

 

Architectural acoustics

 

Transducer evaluation and correction

 

Echo detection and analysis

 

Vibration analysis

 

Underwater acoustics

Summary of Contents for Compact VariO UPJ-1P

































Reviews: