manualshive.com logo in svg

Metz Connect EWIO 2, User Manual

Share
Download
Metz Connect EWIO 2 User Manual Download Page 90

 

 

 

 

 

EWIO

2

 User Manual 

V 1.1 | Stand 10/2020 

 Seite 90 von 96 

 

 

METZ CONNECT GmbH | Im Tal 2 | 78176 Blumberg | Germany  
Tel. +49 7702 533-0 | Fax +49 7702 533-433 
For additional documentations look at www.metz-connect.com 

To test this script, log in to the EWIO

2

 and put the content from above into a file named for 

example „meas_and ctrl.sh“ in „/usr/bin“ using the vi editor. 

Change the permission of the file to 755.  
Make sure the digital outputs 1 and 2 are not in manual mode. Set the range of the AI1 to 0-

10 Volt using a GUI client. 
Activate the script, how is described in chapter 

10.5.4.1.

, and apply different voltages to AI1.  

If the applied voltage is lower than 3.5 Volt, the DO1 will be turned on, otherwise turned off. 
Increase the voltage over 7.5 Volt; the DO2 will be turned on. If the input voltage falls under 
7.5 Volt, the DO2 will be turned off. 

 

11.7.

 

Sensor IDs for the analog inputs and their meaning 

 

Sensor  string Name 

enum Unit 

Minimum 

Maximum 

enum Sensor 

enum Range 

1 

"0-10V %" 

UNITS_PERCENT 

0.0 

100.0 

ewioSensor_0_10V_Percent 

ewioRange_Volt 

2 

"0-5V % Pullup" 

UNITS_PERCENT 

0.0 

100.0 

ewioSensor_0_5V_Percent_PU 

ewioRange_Volt_PU 

3 

"0-10 Volt" 
UNITS_VOLTS 

0.0 
10.0 

ewioSensor_0_10V 
ewioRange_Volt 

4 

"0-5 Volt Pullup" 

UNITS_VOLTS 

0.0 

5.0 

ewioSensor_0_5V_PU 

ewioRange_Volt_PU 

5 

"Ohm" 

UNITS_OHMS 

40.0 

4E6 

ewioSensor_Ohm_2Wire 

ewioRange_Ohm_2Wire 

6 

"User Defined" 

UNITS_NO_UNITS 

0.0 

0.0 

ewioSensor_UserDef 

ewioRange_Modes ??? 

7 

"PT100" 

UNITS_DEGREES_CELSIUS 

-50.0 

150.0 

ewioSensor_PT100 

ewioRange_Ohm_2Wire 

8 

"PT500" 

UNITS_DEGREES_CELSIUS 

-50.0 

150.0 

ewioSensor_PT500 

ewioRange_Ohm_2Wire 

9 

"PT1000" 
UNITS_DEGREES_CELSIUS 

-50.0 
150.0 

ewioSensor_PT1000 
ewioRange_Ohm_2Wire 

10 

"NI1000-TC5000" 

UNITS_DEGREES_CELSIUS 

-50.0 

150.0 

ewioSensor_NI1000_TC5000 

ewioRange_Ohm_2Wire 

11 

"NI1000-TC6180" 

UNITS_DEGREES_CELSIUS 

-50.0 

150.0 

ewioSensor_NI1000_TC6180 

ewioRange_Ohm_2Wire 

12 

"BALCO500" 

UNITS_DEGREES_CELSIUS 

-50.0 

150.0 

ewioSensor_BALCO500 

ewioRange_Ohm_2Wire 

13 

"KTY81_110" 

UNITS_DEGREES_CELSIUS 

-50.0 

150.0 

ewioSensor_KTY81_110 

ewioRange_Ohm_2Wire 

14 

"KTY81_210" 
UNITS_DEGREES_CELSIUS 

-50.0 
150.0 

ewioSensor_KTY81_210 
ewioRange_Ohm_2Wire 

Summary of Contents for EWIO 2

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands