METRObility Optical Systems R821-1S Installation And User Manual Download Page 48

Page: 48 / 127

Radiance 10/100 Mbps Services Line Card

Management Frames in Q-in-Q Mode

The R821 provides two options to forward management frames in Q-in-Q

mode when the management channel is tagged. One option encapsu-

lates IP-based management frames and the other bypasses tagging. If

encapsulation is selected, a management frame will egress double-

tagged with both the service provider’s tag and the management VLAN

tag. If bypass is selected, a management frame will egress single-tagged

with only the management VLAN tag.

If no management VLAN is configured, outbound management frames

always egress untagged regardless of whether encapsulate or bypass is

selected.

The following table displays how management frames are forwarded in

Q-in-Q mode under various conditions.

Encapsulate/Bypass

Mgmt VLAN

Mgmt Frame Tag

Encapsulate

Yes

Double-tagged

Encapsulate

Untagged

Bypass

Untagged

Bypass

Yes

Single-tagged

R821

Access

Port

Trunk

Port

Q-in-Q Mode

PVID = 2

(p-bits = assigned queue)

untagged

tagged

double-tagged

untagged

dropped

priority-tagged

tagged without PVID

Summary of Contents for R821-1S
































































































































Search results

Summary of Contents for R821-1S

Reviews:

Related manuals for R821-1S

Brands by name

Popular brands

METRObility Optical Systems R821-1S, Installation And User Manual

Search results

Summary of Contents for R821-1S

Reviews:

Related manuals for R821-1S

Brands by name

Popular brands