Metra Electronics Saddle Tramp BC-DSPX-HD2 Installation Instructions Manual Download | Manualshive

Page: 13 / 24

background image

13

REV. 10/15/21 INSTBC-DSPX-HD2

CROSSOVER ADJUST

MOBILE APP

If installing a subwoofer, the front and rear outputs will default to a 100Hz high pass
filter to keep the low frequency signals out. If a subwoofer is not being installed, change
the front and rear crossover points down to 20Hz for a full range signal, or to the lowest
frequency the speakers will play down to.

Selecting

High Pass

and

Low Pass

will provide one crossover frequency adjustment.

Band

Pass

should only be chosen if installing just front speakers, with one dedicated amp for

the woofers/mids, a second dedicated amp for the tweeters, along with a subwoofer.

Select the desired crossover slope, 24db, 36db, or 48 db. Higher is steeper, but it is
recommended that one uses

High Pass/24db

octave slopes for crossovers on a bike.

«
...
11
12
13
14
15
...
»

Summary of Contents for Saddle Tramp BC-DSPX-HD2

























Reviews:

No comments

Related manuals for Saddle Tramp BC-DSPX-HD2

LevelMaster 7100

Brand: ABB Pages: 28

Ability Smart Sensor

Brand: ABB Pages: 4

Brand: ABB Pages: 20

Brand: Acdeos Pages: 38

Brand: Baintech Pages: 7

Brand: Baicheng Innovations Pages: 32

Brand: Daihatsu Pages: 485

MES ACURAS HEAD

Brand: Barco Pages: 131

Brand: Jeep Pages: 25

Brand: Gates Underwater Products Pages: 49

Brand: Gates Underwater Products Pages: 45

Brand: LAZER Pages: 6

Brand: ICON ProAudio Pages: 29

Brand: Unisen Pages: 9

Brand: Zavoli Pages: 26

Brand: Xerox Pages: 16

Brand: pleasant hearth Pages: 6

Brand: R&G Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands