Metra Electronics RTKP, Technical Manual

Page: 7 / 12

Page 7
Reader Terminal Keypad Technical Manual

Network address
After installation is complete, the device network address must be set by DIP switches.

NOTE

Each Metra device must have different address setting.
Switch #1 must be set to OFF (switch down).
Look up the code for desired address in the coding table. Set switches #2 through #8 to indicated
positions, where:

0 indicates the corresponding switch is in OFF position (switch down)

1 indicates the corresponding switch is in ON position (switch up)
Coding table:
switch positions
address
switch positions
address
2 3 4 5 6 7 8 2 3 4 5 6 7 8
0 0 0 0 0 0 0 100 1 0 0 0 0 0 0 164
0 0 0 0 0 0 1 101 1 0 0 0 0 0 1 165
0 0 0 0 0 1 0 102 1 0 0 0 0 1 0 166
0 0 0 0 0 1 1 103 1 0 0 0 0 1 1 167
0 0 0 0 1 0 0 104 1 0 0 0 1 0 0 168
0 0 0 0 1 0 1 105 1 0 0 0 1 0 1 169
0 0 0 0 1 1 0 106 1 0 0 0 1 1 0 170
0 0 0 0 1 1 1 107 1 0 0 0 1 1 1 171
0 0 0 1 0 0 0 108 1 0 0 1 0 0 0 172
0 0 0 1 0 0 1 109 1 0 0 1 0 0 1 173
0 0 0 1 0 1 0 110 1 0 0 1 0 1 0 174
0 0 0 1 0 1 1 111 1 0 0 1 0 1 1 175
0 0 0 1 1 0 0 112 1 0 0 1 1 0 0 176
0 0 0 1 1 0 1 113 1 0 0 1 1 0 1 177
0 0 0 1 1 1 0 114 1 0 0 1 1 1 0 178
0 0 0 1 1 1 1 115 1 0 0 1 1 1 1 179
0 0 1 0 0 0 0 116 1 0 1 0 0 0 0 180
0 0 1 0 0 0 1 117 1 0 1 0 0 0 1 181
0 0 1 0 0 1 0 118 1 0 1 0 0 1 0 182
0 0 1 0 0 1 1 119 1 0 1 0 0 1 1 183
0 0 1 0 1 0 0 120 1 0 1 0 1 0 0 184
0 0 1 0 1 0 1 121 1 0 1 0 1 0 1 185
0 0 1 0 1 1 0 122 1 0 1 0 1 1 0 186
0 0 1 0 1 1 1 123 1 0 1 0 1 1 1 187
0 0 1 1 0 0 0 124 1 0 1 1 0 0 0 188
0 0 1 1 0 0 1 125 1 0 1 1 0 0 1 189
0 0 1 1 0 1 0 126 1 0 1 1 0 1 0 190
0 0 1 1 0 1 1 127 1 0 1 1 0 1 1 191
0 0 1 1 1 0 0 128 1 0 1 1 1 0 0 192
0 0 1 1 1 0 1 129 1 0 1 1 1 0 1 193
0 0 1 1 1 1 0 130 1 0 1 1 1 1 0 194
0 0 1 1 1 1 1 131 1 0 1 1 1 1 1 195
0 1 0 0 0 0 0 132 1 1 0 0 0 0 0 196
0 1 0 0 0 0 1 133 1 1 0 0 0 0 1 197
0 1 0 0 0 1 0 134 1 1 0 0 0 1 0 198