Metra Electronics 99-2003 Installation Instructions Manual Download Page 1

Page: 1 / 52

INSTALLATION INSTRUCTIONS FOR PART 99-2003

1-800-221-0932

www.metraonline.com

Phillips Screwdriver • Utility Knife • Socket Wrench

KIT FEATURES

APPLICATIONS

GM/SUZUKI MULTI KIT

• DIN Head Unit Provisions with Pocket
• ISO DIN Head Unit Provisions with Pocket
• Double DIN head unit provision
• Stacked ISO head unit provision

A) Radio Housing w/ Pocket • B) ISO Trim Plate • C) DDIN Trimplate • D) DDIN Stacked ISO Brackets
E) DIN Spacer • F) ISO Snap In Brackets • G) Carriage Bolts • H) Kep Nuts • I) (3) Screws/(3) Speed Clips

KIT COMPONENTS

TOOLS REQUIRED:

99-2003

WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• Wiring Harness - Please see www.metraonline.com

for specific interface applications

• Antenna Adapter -
• 40-GM10 - GM Antenna Adapter 1988-up
• 40-CR10 - Chrysler Antenna Adapter 2002-up

Summary of Contents for 99-2003





















































Search results

Summary of Contents for 99-2003

Reviews:

Related manuals for 99-2003

Brands by name

Popular brands

Metra Electronics 99-2003, Installation Instructions Manual

Search results

Summary of Contents for 99-2003

Reviews:

Related manuals for 99-2003

Brands by name

Popular brands