Metal-Fach ecoMAX860P TOUCH Operating Manual Download Page 5

 

2

 

General information 

Boiler  regulator  ecoMAX860P  TOUCH  is  a 
modern electronic device intended to control 
boiler  operation  with  automatic  feeding  of 
solid  fuel  and  with  the  ignitors.  Flame  is 
detected  via  the  exhaust  temperature 
sensor. 
The regulator is a multipurpose device: 

 

it automatically maintains a preset boiler 
temperature  by  controlling  the  fuel 
combustion process, 

 

it  controls  timing  fuel  feeder  and  fan 
(modulating its power), 

 

it  automatically  stabilizes  a  preset 
temperature  of  the  domestic  hot  water 
container, 

 

it 

automatically 

maintains 

preset 

temperature  of  several  independent 
mixer heating cycles. 

The preset temperature of heating cycles and 
the  boiler  can  be  set  on  the  basis  of  a 
weather sensor readouts.  
The  device  includes  the  control  panel  with 
horizontal regulation of its position, the main 
operating  unit  and  optional  modules  to 
control additional heating circuits.  
The  regulator  can  cooperate  with  an 
additional  room  panel  ecoSTER  TOUCH 
situated in living quarters and module for the 
web WiFi ecoNET300.  
It  can  be  used  in  a  household  and  similar 
facilities,  as  well  as  in  lightly  industrialized 
facilities. 

3

 

Information about documentation 

The regulator manual is a supplement for the 
boiler  manual.  In  particular,  except  for  this 
manual,  the  boiler  manual  should  also  be 
observed.  The  regulator  manual  is  divided 
into  two  parts:  for  user  and  fitter.  Yet,  both 
parts 

contain 

important 

information, 

significant  for  safety  issues,  hence  the  user 
should read both parts of the manual. 
We  are  not  responsible  for  any  damages 
caused  by  failure  to  observe  these 
instructions. 

4

 

Storage of documentation 

This assembly and operation manual, as well 
as  any  other  applicable  documentation, 
should  be  stored  diligently,  so  that  it  was 

available at any time. In the case of removal 
or  sale  of  the  device,  the  attached 
documentation should be handed over to the 
new user / owner. 

5

 

Applied symbols 

In this manual the following graphic symbols 
are used: 
 

 - useful information and tips, 

  -  important  information,  failure  to 

observe  these  can  cause  damage  of 
property,  threat  for  human  and 
household animal health and life. 

Caution:  the  symbols  indicate  important 
information,  in  order  to  make  the  manual 
more  lucid.  Yet,  this  does  not  exempt  the 
user  from  the  obligation  to  comply  with 
requirements  which  are  not  marked  with  a 
graphic symbol. 

6

 

Directive WEEE 2012/19/UE  

Act 

on 

electrical 

and 

electronic 

equipment.  

 

 

Recycle the product and the packaging at 
the  end  of  the  operational  use  period  in 
an appropriate manner. 

 

Do  not  dispose  of  the  product  together 
with normal waste. 

 

Do not burn the product. 
 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for ecoMAX860P TOUCH













































Reviews: