background image

revision 1.0

Intercom

Operating Instructions

4 Intended use

Transmission of audio signals via fiber over long distances without signal losses

Use of the optimized components from mk messtechnik GmbH only (correct optical fiber, charger, batteries)

Charging of the batteries with provided chargers from mk messtechnik GmbH only

Non-OEM parts, e.g. power supply modules influence the EMC performance and may cause damages to the 
system

5 Disclaimer of Warranty/Exclusion of Liability

§

Under the Following Circumstances the Warranty and Liability is Excluded:

Usage not according to the intended purpose and misapplication

Non-observance of the safety instructions

Manipulation and modification of the devices

6 Special Regulations and Notes

The following regulations have to be respected for all devices. Additionally, all the specific notes for each device 
have to be respected (see the following chapters).

6.1 Safety

Interferences that are not described in chapter 11, and any damage of the devices (e.g. damaged housing or 
damaged cables at the charger) have to be reported to the responsible expert immediately.
The affected device has to be decommissioned by the responsible expert and must be protected against incorrect 
usage until all damages have been repaired.

6.2 Product Care and Maintenance

Battery packs of the devices have to be maintained on a regular basis (see chapter 9).

Charging of the battery packs has to be done according to the instructions described in chapter 9.3.

Other components of the devices are maintenance free.

Repairs must only be done by the manufacturer.

§

Risk of fire, injury, and damage to the electronics

There are no user serviceable parts in the devices. Opening the devices can lead to short 
circuits if powered components touch the housing of the device. Therefore NEVER open the 

housings, because there is a risk of fire or injury!
In case of errors consider the notes in chapter 11. If an an error cannot be solved by 
considering these notes, please send the device in for repair. In this case please contact mk 

messtechnik GmbH BEFORE you send in the device.

Page 6 / 23

Distributed by: Reliant EMC LLC, 3311 Lewis Ave, Signal Hill CA 90755, 408­916­5750, www.reliantemc.com

 

Summary of Contents for dAV-TRX
























Reviews: