manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 42 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 42

 

Logical Input 

Description 

Drive not Ready 

This drive feedback input is used to indicate that the feeding 
device drive is not ready to run. The state of the input is 
combined with other states to form the 

Ready

 Logical Output. It 

has no other effect, unless you make it qualify a Warning or 
Fault. 

Drive Overload 

This drive feedback input is used to indicate that the feeding 
device drive is overloaded. With most drives, the feeding 
device will keep running, at least for a while. It has no other 
effect, although you should configure it to qualify a Warning. 

Available I/0 1-8 

These logical I/O points are not used by any function in the 
controller. Since they are both Logical Inputs and Logical 
Outputs, you can use them for control purposes. If you map a 
Physical Input to one of them, and then map a Physical Output 
to the same point, the Output will follow the Input, giving you 
one or more extra contacts, some of which can be inverted. 

 

Physical Inputs 

Physical Inputs 

Description 

Always Off  

The input is always Off. 

Always On  

The input is always On. 

Stable Weight  

On when the weight is stable. See Stability Settings on 
page 27. 

Keyboard Locked  

On when the touch screen is locked out by means of 
serial communications. 

Acc Switch 1 through 4  

Access Switches. Not used in this application. 

Keyboard A1 – H4 

Touch Screen Location Codes. You can map a logical 
input to positions on the touch screen. This is useful 
for testing purposes. 

Rack 1 Input 1

 through 

4

 

I/O Rack 1, PCIO 1. 

Rack 2 Input 1

 through 

4

 

I/O Rack 2, PCIO 1. 

Rack 3

 Input 1 through 

4

 

I/O Rack 3, PCIO 2. 

Rack 4

 Input 1 through 

4

  

I/O Rack 4, PCIO 2. 

Extern Inputs 1 – 16 

The external inputs are set by network 
communications. This is useful when you want bits in 
a PLC to control I/O in your Feeder Controller. If 
outputs 

Comm Lost

 or 

DF1 Timeout

 are On all 

external inputs are turned Off. 

Extern Outputs 1 - 16 

It is possible to map a Logical Input to an External 
Output. This is useful if you want to wrap a Logical 
Output back into the controller as a Logical Input. 

 

Digital Outputs Setup 

This screen allows you to change the mapping and properties for the digital outputs. A 
Physical Output is always mapped to a Logical. 

NOTE

   

On Always 

and 

Off Always 

are valid logical inputs. You typically map unused physical 

outputs to 

Off Always

. 

Unused

 is the same as 

Off Always

. 

35.00.EX O&M Manual 

 

38 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments