manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 26 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 26

 

SETTING UP YOUR CONTROLLER 

Since there are many parameters to set, they are divided into categories. They are 
available from two setup screens. You reach the first (Settings Menu) from the Action 
Menu, by pushing the 

Settings menu

 button. 

 

Settings Menu 

You reach the second (Inputs & Outputs Menu), with I/O related parameters, by pushing 

Inputs & Outputs

. 

 

Inputs and Outputs Menu 

Most values are entered via a numeric entry screen. It shows the name of the parameter, 
the current value, units and the minimum and maximum allowed. If there are three or 
more related parameters, the controller displays three at a time; otherwise it will only 
show one parameter. The active parameter is enclosed in a rectangle. Any button entry 
will act upon this value.  

 

Typical Numeric Entry Screen 

First, find the value by using the Up or Down arrow buttons to scroll to the parameter to 
be changed. 

Enter the new value for the selected parameter using the numeric buttons. The display 
will show the value as it is entered. 

When done, push the 

Enter

 button to save. The controller will check the number you 

entered. If the number is within the minimum and maximum values, a message will 
appear under the parameter list: 

Parameter Accepted 

If the value is not within the limits, the following message will appear:  

35.00.EX O&M Manual 

 

22 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments