manualshive.com logo in svg

MERRICK MC3 35.00.EX, Operation And Maintenance Manual, Page: 12 / 69

Share
Download
MERRICK MC3 35.00.EX Operation And Maintenance Manual Download Page 12

 

35.00.EX O&M Manual 

 

8 

 

Feeder State Transitions 

During operation, the controller state will follow a sequence. This table lists all possible transitions between states. During normal batching, Next 
State follows the Current State. All other columns indicate to what state the MC³ will go on an external command. To find out what the controller 
will do if you issue a command, start on the row for the current state, and go the column of the command. 

Current State 

Next State 

Start Batch 

Stop Batch 

Start Fill 

Stop Fill 

Start Cleanout 

Stop 
Cleanou
t 

Clear Batch 

Paused 

Note 1 

Stable Chk 
Before 

 

Re-fill 

 

Cleanout weight   

Idle. Note 2 

Idle 

Note 1 

Stable Chk 
Before 

 

Re-fill 

 

Cleanout weight   

Idle. Note 2 

Stable Chk 
Before 

Fast Feed 

 

 

 

 

 

 

Idle. Note 2 

Fast Feed Note 
3 

Fine Feed or 
Re-fill. Note 3 

 

 

 

 

Stable Chk
After, Paused 

 

Stable Chk 
After, Re-fill 

Stable Chk,
Cleanout 

 

 

Idle. Note 2 

Fine Feed Note 
4 

Stable Chk 
After 

 

 

 

Stable Chk
After, Paused 

 

 

Stable Chk 
After, Re-fill 

Stable Chk,
Cleanout 

 

 

Idle. Note 2 

Stable Chk After 

Idle 

 

 

 

 

Cleanout weight   

Idle. Note 2 

Re-fill 

Close Gate

 

 

 

 

 

 

Paused

Stable Chk
Before or Idle 

 

Cleanout weight   

Idle. Note 2 

Close Gate 

Fast Feed or 
Idle 

    

 

 

 

 

 

Idle. 

Note 2

Cleanout weight 

Cleanout time 

 

 

 

 

 

Idle 

Idle. Note 2 

Cleanout time 

Cleanout 
Done 

       

 

 

Idle 

Idle. 

Note 2

Cleanout Done 

Idle 

 

 

Re-fill 

 

 

 

Idle. Note 2 

 

Summary of Contents for MC3 35.00.EX






































































Reviews:

No comments